3D Print lens protector for Mobula8 Materials: TPU Weight: 0.3gram We also provide STL file for download: Lens protector for Mobula8

Sometimes your receiver antennas can get chopped in half in a prop strike or a crash and finding a replacement can be hard without buying a new receiver. Welcome the 2.4GHZ replacement antenna for most FrSky and other receivers on the market now in a 7cm length so no need to worry about having your receiver antennas sticking too far out of your build. Get yours today! IPEX 4 is the smaller type that works on receivers such as R-XSR etc. Please order accordingly. Package Includes 1x Repla…

ELRS Fyujon is a very simple and easy-to-use 2-in-1 module that integrates 5.8GHz video transmission and 2.4GHz ELRS receiver. They can be integrated into a board for use, or they can be split into independent VTX modules and receiver modules to be used separately. They are all open source solutions that are currently very popular with FPV pilots. Compatible with 20mmx20mm, 30mmx30mm stack mounted way and 25.5mmx25.5mm whoop mounted way. Due to the ultra light weight (only2.1gram), it would be a…

This is a micro flysky compatible receiver that is estimated to give you at around 500m range making it one of the best flysky compatible receivers to use on your FPV quadcopter. This receiver uses the AFHDS-2A and is fully compatible with betaflight/iNav. The diversity antennas give you great range and this receiver also outputs RSSI on channel 14, allowing you to keep an eye on your signal to avoid a out of range failsafe. Key Features – Customized for Betaflight – RSSI Display Via O…

The Happymodel ExpressLRS PWM Kit incudes a 6CH EPW6 900MHz Receiver with two antennas and three 6-pin adapters. Perfect for your Fixed Wing airplane! Features Fixeded Wing Receiver Kit EPW6 900MHz PWM RX 915MHz Antenna 868MHz Antenna BINDING PROCEDURE Supply power to the EPW6 RX, wait until the Green LED on the RX is off, immediately turn off the power, and then repeat again the above steps. When the RX is powered on for the third time, the Green LED light will start…

The Happymodel ExpressLRS PWM Kit incudes a 5CH EPW5 2.4GHz Receiver with two antennas and three 6-pin adapters. Perfect for your Fixed Wing airplane! Features Fixeded Wing Receiver Kit EPW5 2.4GHz PWM RX 2.4GHz Antennas BINDING PROCEDURE Supply power to the EPW5 RX, wait until the Green LED on the RX is off, immediately turn off the power, and then repeat again the above steps. When the RX is powered on for the third time, the Green LED light will start to double-f…

The Happymodel 2.4GHz ELRS nano series receiver has an open-source program based on ExpressLRS. There are three in this series. The PP RX is designed by @Jye Smith from the ExpressLRS development team. Its main hardware architecture is STM32L432KBU6 MCU and SX1280 RF chip. It has a built-in ceramic antenna, which is super light and small in size. On the basis of PP RX, Happymodel has have developed the Nano 2.4GHz RX of ESP8285 version named EP1 and EP2. The RF module of EP1/EP2 is the same …

The Happymodel 2.4GHz ELRS nano series receiver has an open-source program based on ExpressLRS. Due to the low-latency and high-refresh-rate RF module, they are very comfortable for FPV Racing and Long Range FPV. These are very suitable for Tiny whoops because of the ultra-light and Nano size! The Series There are three in this series. The PP RX is designed by @Jye Smith from the ExpressLRS development team. Its main hardware architecture is STM32L432KBU6 MCU and SX1280 RF chip. It has a bui…

The Happymodel ExpressLRS F4 is the world’s first AIO 5-in-1 whoop flight controller with a built-in high-performance 2.4GHz ELRS receiver. This F4 flight controller has a built-in 5A ESC, 5.8GHz VTX, and OSD. This AIO is made for 1S long-range and tiny whoops. This FC integrates an SPI-controlled 2.4GHz ExpressLRS receiver, Dshot protocol 4-in-1 ESC, 5.8GHz 40ch video transmitter, and Betaflight OSD. Ultra-small size and ultra-stable remote control range can improve the range of the origina…

The ES900TX module is a long-distance 915mhz wireless transmission developed and designed based on the ExpressLRS open-source software. The ES900TX is characterized by ultra-long-range, stable operation, and low latency. This module is compatible with most Opentx remote controllers, especially suitable for Radiomaster TX16S and Jumper T12, T16, and T18 series remote controllers – basically plug and play. The heat sink has been specially customized for the transmitter module, which can help the t…

The ES900TX and ES900RX modules sets are long-distance 915mhz wireless transmission equipment developed and designed based on the open-source ExpressLRS software. This set of modules is characterized by ultra-long-range, stable operation, and low latency. They are compatible with most Opentx remote controllers, especially suitable for Radiomaster TX16S and Jumper T12, T16, and T18 series remote controllers, and are basically plug and play. The heat sink has been specially customized for the tr…

The ES900RX module is a long-distance 915mhz wireless receiver developed and designed based on the open-source ExpressLRS software. This module is characterized by ultra-long-range, stable operation, and low latency. It is compatible with most Opentx remote controllers, especially suitable for Radiomaster TX16S and Jumper T12, T16, and T18 series remote controllers, and are basically plug and play. Note: Radio and TX Not Included VIDEO: Happymodel ExpressLRS 900mhz TX & RX System …

This SMA Antenna is designed specifically for the ES24TX module by Happymodel which is based on the open-source ExpressLRS – a very popular low latency and high re-flashed rate RF module for RC Airplane and FPV Racing. Its main hardware architecture is ESP32, ESP8285, and the SX1280 RF chip. Note: This is the Antenna only, with SMA Connector. VIDEO: Happymodel ExpressLRS 2.4 Tutorial Guide Specifications Peak Gain Position (Theta) 180.00 Upper Hem. Efficiency (%) 40.55 Lower …

This Micro TX is designed by Happymodel and based on the open-source ExpressLRS which is a very popular low latency and high re-flashed rate RF module for RC Airplane and FPV Racing. Its main hardware architecture is ESP32, ESP8285, and the SX1280 RF chip. The ES24TX module is a complete solution that is plug and play and already pre-loaded with Expresslrs firmware. Features ExpressLRS Firmware Plug and Play Low Latency Specifications MCU:ESP32(main),ESP8285 (aux, as espb…

Happymodel ExpressLRS ELRS Fyujon 2IN1 AIO Module Built-in ELRS 2.4GHz EP Receiver OpenVTX 5.8G 48CH 300mW for FPV Toothpick Cinewhoop Drone OVERVIEW: ELRS Fyujon is a very simple and easy-to-use 2-in-1 module that integrates 5.8GHz video transmission and 2.4GHz ELRS receiver. They can be integrated into a board for use, or they can be split into independent VTX modules and receiver modules to be used separately. They are all open source solutionss that are currently very popular with FPV p…

The Happymodel ExpressLRS CrazyF4 is the world’s first AIO 5-in-1 whoop flight controller with a built-in high-performance 900MHz ELRS receiver. This F4 flight controller has a built-in 5A ESC, 5.8GHz VTX, and OSD. This AIO is made for 1S long-range and tiny whoops. Features Onboard High-performance 900Mhz Serial Based ELRS Receiver Onboard Voltage and Amperage meters World’s first 5-in1 AIO FC w/ Receiver Onboard 4-in-1 ESC F4 Flight Controller Specifications ELRS RECEIV…

This is a 3D Printed JR Bay for the Happymodel ExpressLRS ES24TX / ES915TX. Note: 3D Printed Part only… ES915RX & ES915TX Not Included. VIDEO: HappyModel ES915RX & ES915TX // ExpressLRS // Over 30km! Specifications Color: White Height: 1.29″ Width: 1.94″ Length: 2.5″ Includes 1x 3D Printed JR Bay for the HappyModel ES915RX & ES915TX (White) 1x Hardware Kit 1x Sticky Pad Note: 3D Print only… ES915RX & ES915TX Not Included.

This Lite TX module is designed by Happymodel and based on the open-source ExpressLRS which is a very popular low latency and high re-flashed rate RF module for RC Airplane and FPV Racing. This module works with the Jumper T-Lite. Its main hardware architecture is ESP32, ESP8285, and the SX1280 RF chip. The ES24TX-Lite module is a complete solution that is plug-and-play and already pre-loaded with Expresslrs firmware. Now equipped with a power module to ensure stability in high-powered conditi…

What is a “TX Backpack”? Some of the ExpressLRS TX modules include an additional ESP8285 chip, which lets us communicate wirelessly with other ESP8285 enabled devices using a protocol called espnow. We call this chip the “TX-Backpack”. The aim of the TX-Backpack is to allow wireless communication between ExpressLRS, and other FPV related devices for command and control, or for querying config. Sounds interesting… What type of FPV devices can it talk to? A prime use case is your video recei…

Introduce the World first true diversity 2.4 GHz ExpressLRS Rx with RF amps Item: Happymodel EP1 Dual receiver true diversity 2.4Ghz ExpressLRS RX ESP32 PICO D4, dual SX1280(SX1281) Antenna connector: IPEX MHF 1/U.FL RF Frequency: 2.4GHz (2400~2480MHz) Telemetry power: >19dbm Receiver protocol: CRSF Input voltage: 3.5v~8.4v Recommend +5V DC @ “+” pad PCB size: 19mm x 14mm Weight: 1gram exclude antenna Firmware: ExpressLRS v3.0.0 rc1 or latest version Target: Unified_ESP32_2400_RX, …

This 5-in-1 flight controller is inspired by Happymodel’s Official Pilot – Angry Don FPV ! The Happymodel Diamond F4 AIO 5-IN-1 Flight controller has a built-in VTX, ESC, OSD, and receiver – all on one triangle-shaped whoop board! The 3 corners fit 25.5mm whoop mounting spacing. This is the AIO board included on the ultra-light Happymodel Moblite6/7 whoops. Features Diamond Mounting Pattern – 22.2×22.2×32.7mm Built-in 5V/1A BEC Built-in SPI Frsky Receiver Built-in Betaflight OSD…

This flight controller is inspire from Happymodel Official Pilot “Angry Don FPV“ Flight controller (Flysky SPI RX version)DiamondF4 FS FC Firmware target: CrazybeeF4FS MCU:STM32F411CEU6 (100MHZ, 512K FLASH) Sensor: MPU-6000(SPI connection) Original whoop size compatible Power supply: 1S battery input (DC 2.9V-4.35V) Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready Built-in Betaflight OSD(SPI Control) Built-in 5.8G VTX Built-in SPI Frsky/Flysky receiver Built-in 5V 1A BE…

About this product The Happymodel Diamond F4 AIO 5-IN-1 Flight Controller has a built-in VTX, ESC, OSD, and receiver – all on one triangle-shaped whoop board! The 3 corners fit 25.5mm whoop mounting spacing. This is the AIO board included on the ultra-light Happymodel Moblite6/7 whoops and is inspired by Happymodel’s Official Pilot – Angry Don FPV! VIDEO: Happymodel Diamond F4 Features Diamond Mounting Pattern – 22.2×22.2×32.7mm Built…

These rubber damping balls are shock absorbing and include screws. Compatible with the Happymodel Moblite7. Specifications: Weight: 0.012 kg Used for the Happymodel Moblite7 Includes 4x Long Rubber damping ball 4pcs 4x M1.2*4 Screws