HGLRC ELRS 915MHz receiver: a receiver designed for long-distance flight Product features: Stronger diffraction capability, good stability in dense obstacles Longer flight distance, with a remote control distance of more than 10 kilometers in actual measurements Choose direct plug-in connection or welding connection to meet different application requirements Use the more stable 3.3.0 ELRS firmware, which can be directly used with most remote controllers or high-frequency heads equip…

HGLRC ELRS 2.4G Receiver

HGLRC C1 remote control : an entry-level high-value handle control; 1. Built-in 500mw radio frequency module, which can realize stable signal transmission and remote control distance; 2. The operation procedures are extremely simplified, and common operations such as frequency pairing, power adjustment, and joystick calibration can be realized without a screen, and you can get started quickly; 3. Mix and match design of three-stage switch and two-stage switch; 4. It can be equipped with a wi…

Air Unit Taogolas Antenna 1 x Antenna only Replacement Antenna – same as what is included with standard Herelink

Since the TBS Tango2 radio is powered by 1S, when an external TX module such as ES24TX Slim Pro needs to run at 1000mw, the original circuit structure cannot maintain normal operation or even turn on. This set of power adapters consists of two parts, one of which is a PCB board directly glued to the back of the main board of the Tango2. Another PCB with pins directly replaces the original external expansion module. The overall replacement is very convenient and is plug-and-play. Of course, y…

Speki+ is the upgrade DSM2/DSMX/SRXL protocol compatible Micro 2.4Ghz receiver, it comes with PA module, longer range and stable signal transmission, with RSSI telemetry. You can get the RSSI from Betaflight OSD Specifications : Brand: Happymodel Model Name: Speki+ Weight: 1.2g Dimension: 20mm*12.4mm*5mm Support protocol: DSM2/DSMX Output Signal configuration: SRXL(Set Spektrum2048/SRXL for the serial receiver provider) Antenna connector: I-PEX MHF3 Antenna length: 70mm Input voltage:…

This Multiprotocol TX Module is suitable for many brand’s quadcopters,helicopters and airplanes .You can control RC quadcopters,RC helicopters or RC airplanes flexibility when you insert the TX Module to your Flysky transmitter. You will get many new ways to control the RC models . Description: Item number:MTXI6 Item name: Multi-protocol TX Module Signal frequency: 2400-2483.5Mhz Controllable range: ≈100m Input voltage: 3.7-4.2V (1S battery) Supported remote controls: Flysky FS-i6 FS-i6…

A 2.4GHz antenna from Happymodel. Made for their ExpressLRS Module, but can work with any 2.4GHz SMA device. Specifications Frequency (MHz): 2400.0 Efficiency (dBi): -2.94 Gain (dBi): 4.18 Efficiency (%): 50.77 Directivity (dB): 7.12 Peak Gain Position (Theta): 0.00 Peak Gain Position (Phi): 270.00 Weight(gram): 5.83 Length(mm)*width(mm): 69*45 Plug type: SMA Includes 1x Happymodel 2.4GHz Moxon antenna

Happymodel Molding JR Bay mounting case for ES24TX and ES915TX ExpressLRS TX module SPECIFICATIONS : Brand Name: Happymodel Materials: Nylon Color: Black Standard JR Bay dimension Weight: 28gram Available for ES24TX ES915TX. Need a bit mod to the aluminum alloy heat sink while use with ES915TX module. Reserved cooling fan installation position, support 20x20x6mm fan. PACKAGE INCLUDES: 1 x Happymodel Molding JR Bay mounting case for ES24TX and ES915TX ExpressLRS TX…

Frequency: 915 MHz or 868MHz optional Polarization: Horizontal polarization Impedance: 50 Ω S.W.R.: <= 1.7 Antenna Gain: 2.0DBi Working Temp: -40~80℃ Humidity: 95%~100% RH RF Cable : RG1.13 Connector: IPEX1 Weight: 1 g Cable Length: 85 mm Width: 42mm~44mm Compatibility: Happymodel ES900RX , TBS CROSSFIRE NANO RX

Sometimes your receiver antennas can get chopped in half in a prop strike or a crash and finding a replacement can be hard without buying a new receiver. Welcome the 2.4GHZ replacement antenna for most FrSky and other receivers on the market now in a 7cm length so no need to worry about having your receiver antennas sticking too far out of your build. Get yours today! IPEX 4 is the smaller type that works on receivers such as R-XSR etc. Please order accordingly. Package Includes 1x Repla…

ELRS Fyujon is a very simple and easy-to-use 2-in-1 module that integrates 5.8GHz video transmission and 2.4GHz ELRS receiver. They can be integrated into a board for use, or they can be split into independent VTX modules and receiver modules to be used separately. They are all open source solutions that are currently very popular with FPV pilots. Compatible with 20mmx20mm, 30mmx30mm stack mounted way and 25.5mmx25.5mm whoop mounted way. Due to the ultra light weight (only2.1gram), it would be a…

This is a micro flysky compatible receiver that is estimated to give you at around 500m range making it one of the best flysky compatible receivers to use on your FPV quadcopter. This receiver uses the AFHDS-2A and is fully compatible with betaflight/iNav. The diversity antennas give you great range and this receiver also outputs RSSI on channel 14, allowing you to keep an eye on your signal to avoid a out of range failsafe. Key Features – Customized for Betaflight – RSSI Display Via O…

The Happymodel ExpressLRS PWM Kit incudes a 6CH EPW6 900MHz Receiver with two antennas and three 6-pin adapters. Perfect for your Fixed Wing airplane! Features Fixeded Wing Receiver Kit EPW6 900MHz PWM RX 915MHz Antenna 868MHz Antenna BINDING PROCEDURE Supply power to the EPW6 RX, wait until the Green LED on the RX is off, immediately turn off the power, and then repeat again the above steps. When the RX is powered on for the third time, the Green LED light will start…

The Happymodel ExpressLRS PWM Kit incudes a 5CH EPW5 2.4GHz Receiver with two antennas and three 6-pin adapters. Perfect for your Fixed Wing airplane! Features Fixeded Wing Receiver Kit EPW5 2.4GHz PWM RX 2.4GHz Antennas BINDING PROCEDURE Supply power to the EPW5 RX, wait until the Green LED on the RX is off, immediately turn off the power, and then repeat again the above steps. When the RX is powered on for the third time, the Green LED light will start to double-f…

The Happymodel 2.4GHz ELRS nano series receiver has an open-source program based on ExpressLRS. There are three in this series. The PP RX is designed by @Jye Smith from the ExpressLRS development team. Its main hardware architecture is STM32L432KBU6 MCU and SX1280 RF chip. It has a built-in ceramic antenna, which is super light and small in size. On the basis of PP RX, Happymodel has have developed the Nano 2.4GHz RX of ESP8285 version named EP1 and EP2. The RF module of EP1/EP2 is the same …

The Happymodel 2.4GHz ELRS nano series receiver has an open-source program based on ExpressLRS. Due to the low-latency and high-refresh-rate RF module, they are very comfortable for FPV Racing and Long Range FPV. These are very suitable for Tiny whoops because of the ultra-light and Nano size! The Series There are three in this series. The PP RX is designed by @Jye Smith from the ExpressLRS development team. Its main hardware architecture is STM32L432KBU6 MCU and SX1280 RF chip. It has a bui…

The ES900TX module is a long-distance 915mhz wireless transmission developed and designed based on the ExpressLRS open-source software. The ES900TX is characterized by ultra-long-range, stable operation, and low latency. This module is compatible with most Opentx remote controllers, especially suitable for Radiomaster TX16S and Jumper T12, T16, and T18 series remote controllers – basically plug and play. The heat sink has been specially customized for the transmitter module, which can help the t…

The ES900TX and ES900RX modules sets are long-distance 915mhz wireless transmission equipment developed and designed based on the open-source ExpressLRS software. This set of modules is characterized by ultra-long-range, stable operation, and low latency. They are compatible with most Opentx remote controllers, especially suitable for Radiomaster TX16S and Jumper T12, T16, and T18 series remote controllers, and are basically plug and play. The heat sink has been specially customized for the tr…

The ES900RX module is a long-distance 915mhz wireless receiver developed and designed based on the open-source ExpressLRS software. This module is characterized by ultra-long-range, stable operation, and low latency. It is compatible with most Opentx remote controllers, especially suitable for Radiomaster TX16S and Jumper T12, T16, and T18 series remote controllers, and are basically plug and play. Note: Radio and TX Not Included VIDEO: Happymodel ExpressLRS 900mhz TX & RX System …

This SMA Antenna is designed specifically for the ES24TX module by Happymodel which is based on the open-source ExpressLRS – a very popular low latency and high re-flashed rate RF module for RC Airplane and FPV Racing. Its main hardware architecture is ESP32, ESP8285, and the SX1280 RF chip. Note: This is the Antenna only, with SMA Connector. VIDEO: Happymodel ExpressLRS 2.4 Tutorial Guide Specifications Peak Gain Position (Theta) 180.00 Upper Hem. Efficiency (%) 40.55 Lower …

This Micro TX is designed by Happymodel and based on the open-source ExpressLRS which is a very popular low latency and high re-flashed rate RF module for RC Airplane and FPV Racing. Its main hardware architecture is ESP32, ESP8285, and the SX1280 RF chip. The ES24TX module is a complete solution that is plug and play and already pre-loaded with Expresslrs firmware. Features ExpressLRS Firmware Plug and Play Low Latency Specifications MCU:ESP32(main),ESP8285 (aux, as espb…

Happymodel ExpressLRS ELRS Fyujon 2IN1 AIO Module Built-in ELRS 2.4GHz EP Receiver OpenVTX 5.8G 48CH 300mW for FPV Toothpick Cinewhoop Drone OVERVIEW: ELRS Fyujon is a very simple and easy-to-use 2-in-1 module that integrates 5.8GHz video transmission and 2.4GHz ELRS receiver. They can be integrated into a board for use, or they can be split into independent VTX modules and receiver modules to be used separately. They are all open source solutionss that are currently very popular with FPV p…

This is a 3D Printed JR Bay for the Happymodel ExpressLRS ES24TX / ES915TX. Note: 3D Printed Part only… ES915RX & ES915TX Not Included. VIDEO: HappyModel ES915RX & ES915TX // ExpressLRS // Over 30km! Specifications Color: White Height: 1.29″ Width: 1.94″ Length: 2.5″ Includes 1x 3D Printed JR Bay for the HappyModel ES915RX & ES915TX (White) 1x Hardware Kit 1x Sticky Pad Note: 3D Print only… ES915RX & ES915TX Not Included.