200A – Current measurement sensor board, based on Allegro Hall Sensor ACS-200U. This Sensor board needs a power supply. So please select the matching BEC according your preference from the BEC section. The BEC will also power the flight controller as well as the attached equipment like GPS, telemetry… etc. The voltage reading of the LiPo is optimised for up to 6S LiPo packs. The board comes with 10cm connection cable (DF-13-6p <-> DF-13-6p) to the FC. If you need a customized cable in…

100A – Current / Voltage measurement sensor board, based on Allegro Hall Sensor ACS758-100U. Voltage range is up to 20S (85V) with solder bridge open and up to 7S (30V) with solder bridge closed. Please check the maual page for more details. This Sensor board connects directly to any Premium-Line BEC or Sensor Hub X2-V2. Connected to the sensor are 2x10cm AWG12 wire (red) as a standard. REM: The connector is Molex / Clik-Mate / 1.25mm / 4p (5023800400) Without CFK enclosure = 27.5 x 19.5 x 10.5m…

50A – Current / Voltage measurement sensor board, based on Allegro Hall Sensor ACS758-050U. Voltage range is up to 14S (60V) with solder bridge open and up to 7S (30V) with solder bridge closed. Please check the manual page for more details. This Sensor board connects directly to any Premium-Line BEC or Sensor Hub X2-V2. Connected to the sensor are 2x10cm AWG12 wire (red) as a standard. REM: The connector is Molex / Clik-Mate / 1.25mm / 4p (5023800400) Without CFK enclosure = 27.5 x 19…

MATEKSYS PM12S-3 Power Module The MATEKSYS PM12S-3 Power Module features 9-55V DC IN (3-12S LiPo), 3x independent Step-Down Voltage Regulators and BEC 5V, 4A continuous, 6A Peak, BEC 12V 4A continuous, 6A Peak and BEC Vx, 5.25V/6V/8V options, 15A cont., 25A Peak 1K:20K voltage divider built-in (Volt 1/21 Input voltage). Note: If the input voltage is noisy, capacitor is required to be soldered to the input pads. Features BEC Vx, 5.25V/6V/8V options,…

MATEKSYS Optical Flow & Lidar Sensor – 3901-L0X This sensor works the same way as an optical mouse, helping your iNAV quad maintain position without GPS! This module also integrates a laser time-of-flight range sensor. Specifications Optical Flow: PMW3901 Lidar: VL53L0X Interface UART Protocol: INAV MSP Working Range: 8cm~200cm Field of view: 42 degree(PMW3901), 27 degree(VL53L0X) Minimum Illumination >60Lux Input voltage: 4.5~5.5V Power Consumption: 40mA Size: 36*12mm,…

MATEKSYS MICRO BEC 6-30V TO 5V/9V-ADJ (3PCS) High Efficiency Synchronous Step-down regulator SPECIFICATION High Efficiency Synchronous Step-down regulator Wide 6V to 30V Operating Input Range Continuous load current: 1.5 Amps (Max.2.5A 5s/minute) VOut 5V or 9V Adj. Default is 5V. VOut Load Regulation: 2% Standby current: <5mA Maximum Duty Cycle: 95% OCP Protection and Hiccup Thermal Shutdown Output Short-circuit tolerant (5 seconds/minute) Pins distance: 2.54mm Size…

MATEKSYS M10Q-5883 GNSS & COMPASS The MATEKSYS M10Q-5883 supports GNSS (GPS, GLONASS, Galileo, and BeiDou) and thus offers excellent RF sensitivity. The SAM-M10Q uses a multi-constellation GNSS module powered by u-blox SAM-M10Q-00B. The SAM-M10Q features the u-blox M10 standard precision GNSS platform and provides exceptional sensitivity and acquisition time for all L1 GNSS signals. This feature will help you pick up the best signals. But also enhance the dynamic position accuracy with small a…

Description MATEKSYS H743-SLIM V3 FLIGHT CONTROLLER The MATEKSYS H743-SLIM V3 Flight Controller arrives with new features and improvements over the original! This FC is equipped with STM32H743VI, ICM20602 & MPU6000, DPS310, OSD, 7x UARTs, 2x I2C, 1xCAN, 13x PWM outputs, BEC5V, and much more! UPDATE V3, IMU ICM42688P, ICM42605 Features Equipped with IMU ICM42688P, ICM42605 Specifications MCU: STM32H743VIH6, 480MH…

About this product Introducing the MATEKSYS ExpressLRS 2.4GHz True Diversity Receiver – ELRS R24-TD, your reliable companion for long-range RC control. With true diversity technology, it ensures robust signal reception even in challenging environments. Compatible with ExpressLRS systems, it offers seamless integration and outstanding performance. Say goodbye to signal loss and hello to uninterrupted, precise control with the MATEKSYS ExpressLRS R24-TD. Features Un…

About this product The MATEKSYS ELRS R24 D Receiver is a 2.4GHz ExpressLRS diversity receiver with 22.5dbm Telemetry Power and two IPEX MHF 1 antennas. VIDEO: Mateksys Express LRS receivers ELRS-R24-S and ELRS-R24-D under a microscope Features 22.5dbm Telemetry Power IPEX MHF1 Antennas 2.4GHz Frequency ExpressLRS Specifications Power dissipation: 40~45mA(before binding), 70~75mA(binding), 90~95mA(wifi mode) Diversity (antenna-switching), default ANT2 R…

MATEKSYS 12S Pro BEC – 9-55V To 5V/8V/12V – 5A The MATEKSYS 12S Pro BEC features a wide 9-55V Operating Input Range, 3x Output Voltage Options 5V/8V/12V and Supports continuous output current of up to 5A, peak current of 9A. This voltage regulator also features a synchronous switching step-down (buck) regulator, thermal Shutdown, output Short-circuit tolerance (2 seconds), overcurrent protection & self-recovery and much more! FEATURES: Synchronous switching st…

MATEK UBEC DUO 4A/5~12V & 4A/5V UBEC DUO Manual This device is a high-efficiency, switch-mode buck regulator with two output channels, works with 7~26Vdc input. One output channel is capable of supplying 0~4A/5V for your RX or Flight Controller. This device also features another output channel with 4A & 5~12V (adjustable), inbuilt power switch that is operated by a spare Aux Channel, this feature can also be used to power and switch on/off a wide variety of electric equip…

SAM-M10Q uses multi-constellation GNSS module powered by u-blox SAM-M10Q-00B. The SAM-M10Q features the u-blox M10 standard precision GNSS platform and provides exceptional sensitivity and acquisition time for all L1 GNSS signals. SAM-M10Q supports concurrent reception of four GNSS (GPS, GLONASS, Galileo, and BeiDou). The high number of visible satellites enables the receiver to select the best signals. This maximizes the position availability, in particular under challenging conditions such as…

MATEK PM20S-2 POWER MODULE 3~20S INPUT W/ 2X BEC The MATEKSYS PM20S-2 Power Module features 9-85V DC IN (3-20S LiPo) and 2 x independent Step-Down Voltage Regulators (BEC1 and BEC2) SPECIFICATIONS: PM20S-2 is made with 100V DC components. Support 9V to 85V DC operating Input voltage with 85V TVS protection 2x independent Step-Down Voltage Regulators Regulator 1 , 5.3V / 6.1V / 8.1V output options. supports typical continuous output current of up to 15A, Peak current…

Matek Micro BEC 6-60V to 5V/9V/12V. Get the voltage you need with this Matek BEC, convert 6-60V to either 5V, 9V, or 12V. This BEC defaults to 5V, select either 9V or 12V by soldering the respective jumper. Specifications Wide 6V to 60V Operating Input Range Start-up Voltage >=6.7V VOut 5V, 9V or 12V Adj. Default is 5V. Maximum Duty Cycle: 100%, when input voltage< setting value, Regulator output voltage = Input voltage Continuous load current: Depends on input voltage and h…

1 x Mark4-Accessories

The Mark4 7inch 295mm Carbon Fiber Frame Kit is built specifically to tackle the problems in FPV Racing and video recording with quadcopters. It is known for its toughness and durability. Carbon fiber is mostly an accepted material for frame designing because of its high stiffness to weight ratio. The Carbon Fiber Frames are very rigid and improve stability and flight performance. The frame is lightweight and possesses thick arms, so as to give them good mechanical strength. The frame has a …

The Mark4 10inch V2 is a heavy-duty carbon fiber drone frame engineered for serious long-range FPV flying. Designed to handle massive 10-inch propellers , this frame features a robust 473mm motor-to-motor diagonal and 7.5mm thick carbon arms —ensuring unmatched durability and vibration resistance during aggressive flight. Ideal for analog builds but flexible enough to support digital setups, the Mark4 V2 is built with a modular layout , offering dual stack mounting patterns (30.5×30.5mm…

Motor Data Motor Model MAD Prius FS2810 V1.0 Number of pole pairs 12N14P Motor Size D:33.6 ×37.4 mm Rotor Balance ≤5 mg Propeller Mounting Holes M5 Nut Motor Mounting Holes D:19 M3×4 Shaft Diameter IN: 5 mm Cable Length 250 mm 18# Awg(Black) silicone _________________________________________________________________________________________________________________________________________ Drawing and mount holes

Motor Data Motor Model MAD Thruster FS2306 V1.0 Motor Number of slots 12N14P Motor Size D:28.2 ×32.2 mm Rotor Balance ≤5 mg Propeller Mounting Holes M5 Nut Motor Balance D:16 M3×4 Shaft Diameter IN: 4 mm Cable Length 150 mm 20# Awg(Black) silicone

Clear Sky 1507 V1.0 2500KV Powerful. Efficient. Reliable. The Clear Sky 1507 V1.0 2500KV motor is built for 3–4 inch FPV drones that demand smooth control and high efficiency. Featuring a 12N14P configuration, precision-balanced rotor, and lightweight aluminum bell, it delivers strong torque and stable performance across the full throttle range. With a weight of only 14.2 g , the motor produces up to 741 g of thrust and 442 W of output power on a 6S setup. Its open bell design ensures…

Motor Data Motor Model MAD BSC3115 V1.0 Number of pole pairs 12N14P Motor Size D:37.1 × 48.9 mm Rotor Balance ≤5 mg Propeller Mounting Holes M5 Nut Motor Mounting Holes D:19 M3×4 Shaft Diameter IN: 5 mm Cable Length 250 mm 18# Awg(Black) silicone _________________________________________________________________________________________________________________________________________ Include

Motor Data Motor Model MAD BSC2807 V1.0 Motor Number of slots 12N14P Motor Size D:33.6 × 35.7 mm Rotor Balance ≤5 mg Propeller Mounting Holes M5 Nut Motor Balance D:19 M3×4 Shaft Diameter IN: 5 mm Cable Length 250 mm 18# Awg(Black) silicone ___________________________________________________________________________________________________________________________ Drawing and mount holes Include

This M5 Set of 2 Propeller Nut Cap CW CCW For Brushless DC Motor is the set of two different i.e CW and CCW Nut Cap for 1306 and 3100 brushless motor to be fitted above the propeller. Prop nuts of different directions usually come in different colors, such as black and silver for better user-friendliness. Some mini quad motors are labeled CW and CCW, and it can cause a hell of confusion for a lot of people in this hobby including experienced quadcopter builders. Basically, CW (clockwise) a…