Please Note: Image for representation only! Product Overview FS series A Type aluminium electrolytic capacitors features extreme high capacitance, long life, and low ESR—all wrapped in significantly smaller case sizes. The FS series provides space reduction and allows for a reduced number of capacitors on the board. Low ESR and high ripple current in the FS series combines to provide a more stable, long-life capacitor option. Smaller case size, miniaturized: one size smaller than EEU…

Product Features Hardware design based on PX4-V6 standar. Full adaptation of PX4 firmware (also providing a modified branch of 500HZ IMU rostopic). future maintenance and hardware updates. Hardware features：27mm x 29mm x 9mm Specifications MCU: STM32H743VIH6, 480MHz, 2MB Flash IMU: BMI088+BMI088(DUAL) Baro: SPL06 MicroSD Card Slot 7x UART 8x PWM 1x I2C 1x SPI 1x SWD 2x ADC (VBAT, Current) USB Type-C BEC 5V 2.5A output (for controller, receiver, GPS, optica…

Specifications Output Interface : UART/115200/LVTTL Protocol : Micolink/Mavlink/MSP Output Rate : 50Hz Firmware Supported : Ardupilot/PX4/INAV/FMT TOF Range : 6m@90% reflectance/1K Lux; 4m@90% reflectance/70K Lux; Center Wavelength : 940nm Emitting Angle : 2 ° Dead Zone : 2cm Ranging Accuracy : 2cm(<2m@90% reflectance); 1.5%(>2m@90% reflectance) Optical Flow FOV : 42 ° Max Speed Measurement : 7m/s@1m height Ambient Light Demand of Optical Flow : >60Lux Optical…

MicoAir MTF-01P Optical Flow & 12m Range 2IN1 Sensor You’ll achieve greater accuracy in navigation with our MTF-01P Optical flow & 12m Range 2IN1 Sensor, thanks to its advanced technology and 12 meter range. Make smarter decisions and stay in control with our optical sensor solution. SPECIFICATIONS: Output Mode: UART 115200 Output Interface: LVTTL (3.3V) Protocol: Micolink/Mavlink/MSP Output Rate: 100Hz Firmware Supported: Ardupilot/PX4/INAV/FMT(Default firmware flashed is iNav) …

Description MTF-01 is an optical flow ranging integrated sensor developed by MicoAir Technology. It uses uart to output data and is compatible with mainstream open source flight controllers such as Ardupilot, PX4 and INAV. It can be used directly after simple configuration without complicated development process. MTF-01 features an integrated PMW3901 optical flow sensor and a high-performance TOF sensor, which can be used normally in outdoor sunlight environments. Specifications Output…

Description Product ModelMT-15 Product Weight:5.5g Product Size28 * 13.5 * 21mm Output ModeUART/IIC Switchable Measurement Frequency800Hz-5Hz Adjustable Ranging Range0.05-15m Ranging Blind Spot5cm Ranging Accuracy2cm (0.05-2m) 1% (2m-15m) @ 90% Reflectance Object Laser Wavelength830-870nm Resistance To Ambient Light100K Lux Illumination Laser FOV1-2° Laser Safety LevelClass 1 Consumption500mw Working Voltage4.0-5.5V Working Temperature -10°C~60°C

6m ToF Range Sensor, Super mini, outdoor available supports Ardupilot/PX4/INAV

Specifications Output Mode : UART 115200; I2C 400K Output Interface : LVTTL (3.3V) Protocol : Micolink/Mavlink/MSP Output Rate : 800-5Hz (50Hz default) Firmware Supported : Ardupilot/PX4/INAV/FMT TOF Range : 10m@90% reflectance/600Lux; 8m@90% reflectance/70KLux; Center Wavelength : 808nm Emitting Angle : 1.5 ° Dead Zone : 2cm Ranging Accuracy : 4cm(0.02-2m@90% reflectance);2%(>2m@90% reflectance) Light source : LiDAR Power Consumption : 500mW Supply voltage : …

Introduction MG-A01(M10 Ultra) GNSS module integrates a special version of u-blox 10th generation receiver chip – M10050, which run with higher frequency than normal, and the magnetic sensor – QMC5883L. It supports all L1 GNSS signals (GPS/GLONASS/Galieo/BeiDou) and can use up to 32 satellites simultaneously for navigation. The high-gain 25 x 25 x 4mm patch antenna provides the best performance. Built-in flash , parameters can still be saved when module lost power. Why M10 Ul…

Introduction MG-903 GNSS module integrates a u-blox 9th generation receiver chip – M9140 and the magnetic sensor – IST8310. It supports all L1 GNSS signals (GPS/GLONASS/Galieo/BeiDou) and can use up to 32 satellites simultaneously for navigation. The high-gain 20 x 20 x 4mm patch antenna provides the best performance. u-blox M9 receivers support concurrent reception of four GNSS.The high number of visible satellites allows the receiver to select the best signals. This maximizes th…

Introduction MG-902 GNSS module integrates a u-blox 9th generation receiver chip – M9140 and the magnetic sensor – QMC5883L. It supports all L1 GNSS signals (GPS/GLONASS/Galieo/BeiDou) and can use up to 32 satellites simultaneously for navigation. The high-gain 25 x 25 x 4mm patch antenna provides the best performance. u-blox M9 receivers support concurrent reception of four GNSS.The high number of visible satellites allows the receiver to select the best signals. This maximizes t…

Introduction M10G-5883 GNSS module integrates the u-blox 10th generation receiver chip – M10050, and the magnetic sensor – QMC5883L. It supports all L1 GNSS signals (GPS/GLONASS/Galieo/BeiDou) and can use up to 32 satellites simultaneously for navigation. The high-gain 18 x 18 x 4mm patch antenna provides the best balance between performance and small size. Built-in flash , parameters can still be saved when module lost power. Specifications GNSS Receiver: U-BLOX M10 (M1…

Description The LR900-F is a new long-range telemetry radio developed by MicoAir Technology based on LoRa spread spectrum technology. It operates in the 890-915MHz frequency band with a maximum transmission power of 500mW and supports FHSS self-interference hopping mode. With the outdoor RF line-of-sight range of 30km or more, it can provide a reliable point-to-point bidirectional communication link for drones, ships, robots, and RTK devices. It has two ports: one is a TTL serial port, which…

Overview The LR24-F Telemetry Radio is a small, cheap radio with superior performance for flight controller that typically allows ranges of better than 10 kilometers. And it is very suitable for Pixhawk or other Audupilot/PX4 flight controller. It will connect automatically when power up without any configuration unless you need to implement some special features. The LR24-F works in the 2.4GHz, so is better to use 915M receiver (BlackSheep/ELRS 915) than any other 2.4G receiver on your dron…

MicoAir743 flight controller is officially supported by Ardupilot starting from version 4.6, you can update the firmware through Mission Planner or download all the firmware files(Copter/Heli/Plane/Rover/etc) here: ArduPilot Firmware Download Also you can use the online firmware builder provided by Ardupilot to customize your firmware for MicoAir743: ArduPilot Custom Firmware Builder Old version(v4.5.1) firmware can be download here: MicoAir743/Firmware/Ardupilot(v4.5.1) PX4 Mic…

SPECIFICAIONS: Flight Controller MCU: STM32H743VIH6, 480MHz, 2MB Flash IMU: BMI088+BMI270 Baro: SPL06 TF Card Slot 7x UART 9x PWM 1x I2C 1x SWD 2x ADC (VBAT, Current) 1x LED Strip 1x Beeper USB Type-C BEC 5V 2A output (for controller, receiver, GPS, optical flow or other devices) BEC 12V 2A output (for DJI O3/O4/O4 pro) ESC Firmware : AM32_F4A_4IN1_F421_2.17 PWM Freq : 48KHz ESC Protocol : PWM/DShot300/DShot600 (support BDShot) Continuous Current …

Unlock the full potential of your drone with the MicoAir H743 AIO 35A AM32 3-6S Flight Controller & ESC – 25×25mm. With an optimized size and powerful capabilities, this combination is designed for superior control and maximum performance. Get the most out of every flight with MicoAir. You can flash Betaflight , INAV, Ardupilot or PX4 firmware if needed. More information here: MicoAir743-AIO-35A – Flight Controller – MicoAir Tech Flight Controller MCU: STM32H743VIH6, 480M…

The MicoAir F405v2 Flight Controller supports two popular open-source flight control firmwares – INAV and Ardupilot, offering users a wide range of flight control options and customization capabilities. Firmware updates are easily done through Mission Planner or INAV Configurator. Pioneering Integration of the BMI088 IMU: The MicoAir F405v2 is the first flight controller to incorporate the BMI088 IMU and be compatible with INAV firmware. This IMU is renowned for its excellent stability, high …

Description The MicoAir405 v2 is a new cost-effective flight controller runs Ardupilot&INAV firmware, This is the first one which combine the STM32F405 with the high performance IMU sensor BMI088, allowing the flight controllers to have top performance and an attractive price at the same time. The BMI088 is a high-performance 6-axis IMU sensor that comes from Bosch®, its excellent temperature stability and vibration robustness far exceed similar products on the market, making it particularly…

Firmware : AM32_F4A_4IN1_F421_2.17 PWM Freq : 48KHz ESC Protocol : PWM/DShot300/600 Power Input : 2-6S LiPo Continuous Current : 55A * 4 MOSFET RDS(on): 0.75mR Current Sensor Output : 12.75mV/A Mounting : 20*20mm(Φ3mm) / 30.5*30.5mm(Φ4mm) Dimension : 44 * 43.5 * 5.2 mm Weight : 14g

Specifications MCU: STM32H743VIH6, 480MHz, 2MB Flash IMU: BMI088+BMI270 Baro: SPL06 Compass: QMC5883L OSD: AT7456E MicroSD Card Slot 8x UART 11x PWM 1x I2C 1x SWD 2x ADC (VBAT, Current) USB Type-C DJI O3/O4 VTX connector BEC 5V 3A output (for controller, receiver, GPS, optical flow or other devices) BEC 12V 3A output (for video transmitter, camera) Bluetooth Telemetry (connected to UART8 internally, baudrate 115200) VBAT Input Range: 2-6S (6-27V) UART Ma…

Description High Adaptability Voltage Input Support : Suitable for a wide range of voltage inputs from 4-6s, compatible with drones of different sizes and power specifications. From 3-inch mini drones to 7-inch or even larger drones, all can be perfectly matched. BlueJay Firmware Implementation : Equipped with the latest version of BlueJay firmware, utilizing up to 48K of default PWM frequency to effectively reduce electrical noise interference with the IMU, significantly improving flight …

Bluejay-4IN1-60A Firmware : Bluejay_0.19.2_JH40 PWM Freq : 48KHz ESC Protocol : DShot300/600 Power Input : 3-6S LiPo Continuous Current : 60A * 4 MOSFET RDS(on): 0.75mR Current Sensor Output : 12.75mV/A Mounting : 30.5*30.5mm (Φ4mm) Dimension : 44 * 43.5 * 5.2 mm Weight : 13.5g 3D Model Bluejay-4IN1-33A Firmware : Bluejay_0.19.2_JH40 PWM Freq : 48KHz ESC Protocol : DShot300/600 Power Input : 2-6S LiPo Continuous Current : 33A * 4 MOSFE…

Mayatech MT10PRO Motor 10KG Tension Thrust Tester Propeller Power Measurement With Current LCD Display For RC Model Racing Drone Features Support current display function,can display voltage, current rate, discharging power and discharging time. LCD display, visible thrust measurement data Measuring range 0-10kg wide, accurate to 1g Supports conversion between grams and ounces Compatible with a variety of batteries, tester power supply is 5 -26v, support xt-60 connector Compatib…